1.HPMC,Hydroxypropyl Methyl Cellulose
2.Construction:an additive for Mortar&Putty Powder.
3.adhesive for building materials
Hydroxypropyl Methyl Cellulose(HPMC)
1.HPMC, Hydroxypropyl Methyl Cellulose
2.Construction: an additive for Mortar and Putty Powder.
3.adhesive for construction,building materials
1.HPMC,
Hydroxypropyl Methyl Cellulose
2.Construction: an additive for Mortar and Putty Powder.
3.
adhesive
for construction,building materials
1. Application
Hydroxypropyl methylcellulose(HPMC) is widely used as thickener , adhesive, water preserving agent, film-forming agent in construction,building materials.
HPMC specification
Items HK
HPMC content4-12
degree of substitution:0.1-0.3
Ash, wt%
≤1.0
Water, wt%
≤5.0
PH Value
5-7.5
Appearance
White powder or granule
Viscosity mPa.s
See viscosity table
Viscosity (mpas)
Viscosity range of 2% water solution(mpas)
Viscosity (mpas)
Viscosity range of 2% water solution(mpas)
5
3-9
15000
13000-17000
15
10-20
20000
18000-22000
25
20-30
40000
36000-45000
50
40-60
60000
56000-65000
400
300-500
75000
70000-80000
1500
1200-1800
100000
85000-130000
4000
3600-5500
150000
130000-180000
8000
7000-9000
200000
≥180000
10000
9000-11000
Tuesday, September 6, 2011
liquid sealant
liquid sealant accepts sample order
1) good bonding
2) Excellent viscosity
3) waterproof
4) insulativity
liquid sealant
INTRODUCTION
EP106 AB is a two part potting and encapsulating compound. Typical applications include encapsulation, potting and assembly of electronic and magnetic components, such as capacitors, transformers, terminals, industrial magnets, small and large magnetic assemblies, metal detectors, metal separators, magnetic printing cylinders, magnetic holders, insulators, junction boxes, switches, circuit boards. General-purpose casting and bonding for structural and dielectric applications.
PROPERTIES
EP106A
EP106B
Color
Black, white, Clear
Clear amber
Viscosity cps/25°C
10,000~14,000
80~100
Specific gravity
15~1.6
1.0~1.1
APPLICATION CONDITIONS
Mix Rat ion (weight)
EP106A:EP-06B=5:1
Mix Viscosity cps/25
°C
2000~3000
Pot Life (at 25
°C
)
40min (After Mixing)
Cure
25°C×6~8h or 60°C×1h
CURED PROPERTIES
Hardness (Shore D)
88
Volume resistivity (ohm-cm)
>10
15
Surface resistivity (ohm)
>10
14
Dielectric constant (KHZ)
4.2±0.1
Compressive strength (kg/mm
2
)
>25
Bending strength (kg/mm
2
)
>10
Impact strength(kg/mm
2
/cm
2
)
>6
DIRECTIONS FOR USE
1)
Complete cleaning of the substrates should be performed to remove contamination such as oxide layers, dust, moisture, salt and oils which can cause poor adhesion or corrosion in a bonded part.
2) Accurately weigh resin and hardener into a clean container in the recommended ratio. Weighing apparatus having an accuracy in proportion to the amounts being weighed should be used.
3) Don't touch your skin an d eyes, if touch skin, washing with soap water; if touch eyes, washing with water, then get to hospital immediately.
4) Material removed from containers may be contaminated during use. Do not return product to the original container.
STORAGE
Store in original, tightly covered containers in clean, dry areas. Storage information may be indicated on the product container labeling.
Material removed from containers may be contaminated during use. Do not return product to the original container.
PACKING
20Kg/Drum
1) good bonding
2) Excellent viscosity
3) waterproof
4) insulativity
liquid sealant
INTRODUCTION
EP106 AB is a two part potting and encapsulating compound. Typical applications include encapsulation, potting and assembly of electronic and magnetic components, such as capacitors, transformers, terminals, industrial magnets, small and large magnetic assemblies, metal detectors, metal separators, magnetic printing cylinders, magnetic holders, insulators, junction boxes, switches, circuit boards. General-purpose casting and bonding for structural and dielectric applications.
PROPERTIES
EP106A
EP106B
Color
Black, white, Clear
Clear amber
Viscosity cps/25°C
10,000~14,000
80~100
Specific gravity
15~1.6
1.0~1.1
APPLICATION CONDITIONS
Mix Rat ion (weight)
EP106A:EP-06B=5:1
Mix Viscosity cps/25
°C
2000~3000
Pot Life (at 25
°C
)
40min (After Mixing)
Cure
25°C×6~8h or 60°C×1h
CURED PROPERTIES
Hardness (Shore D)
88
Volume resistivity (ohm-cm)
>10
15
Surface resistivity (ohm)
>10
14
Dielectric constant (KHZ)
4.2±0.1
Compressive strength (kg/mm
2
)
>25
Bending strength (kg/mm
2
)
>10
Impact strength(kg/mm
2
/cm
2
)
>6
DIRECTIONS FOR USE
1)
Complete cleaning of the substrates should be performed to remove contamination such as oxide layers, dust, moisture, salt and oils which can cause poor adhesion or corrosion in a bonded part.
2) Accurately weigh resin and hardener into a clean container in the recommended ratio. Weighing apparatus having an accuracy in proportion to the amounts being weighed should be used.
3) Don't touch your skin an d eyes, if touch skin, washing with soap water; if touch eyes, washing with water, then get to hospital immediately.
4) Material removed from containers may be contaminated during use. Do not return product to the original container.
STORAGE
Store in original, tightly covered containers in clean, dry areas. Storage information may be indicated on the product container labeling.
Material removed from containers may be contaminated during use. Do not return product to the original container.
PACKING
20Kg/Drum
High Quality Strong Viscosity Wallpaper Glue
1.Strong Viscosity, High Quality, Odorless and Earth Friendly
2.Applicable to all kinds of wallpaper
3.Easily to use
Adhesive Glue Powder
Product Detail:
1. Net Weight - 180(g)
2. Made by high quality of starch with strong viscosity and high resistance to mold and water
3. Excellent performance in all kinds of wallpaper, especially the ones made by heavy and embossed papers.
4. Qualified for GB 18583-2001
General Speicification:
1. Concentration of Free Formaldehyde - less than 0.01 (g/kg)
2. Concentration of Benzene - less than 0.01 (g/kg)
3. Concentration of Toluene and Dimethylbenzene - less than 0.01 (g/kg)
4. Concentration of Volatile Organic Compounds (VOC) - 2 (g/kg)
Wallpaper Adhesive
Product Detail:
1. Net Weight - 400(g)
2. Excellent performance in all kinds of wallpaper, es pecially the ones made by heavy and embossed papers.
3. Qualified for GB 18583-2008
General Speicification:
1. Concentration of Free Formaldehyde - less than 0.2 (g/kg)
2.Applicable to all kinds of wallpaper
3.Easily to use
Adhesive Glue Powder
Product Detail:
1. Net Weight - 180(g)
2. Made by high quality of starch with strong viscosity and high resistance to mold and water
3. Excellent performance in all kinds of wallpaper, especially the ones made by heavy and embossed papers.
4. Qualified for GB 18583-2001
General Speicification:
1. Concentration of Free Formaldehyde - less than 0.01 (g/kg)
2. Concentration of Benzene - less than 0.01 (g/kg)
3. Concentration of Toluene and Dimethylbenzene - less than 0.01 (g/kg)
4. Concentration of Volatile Organic Compounds (VOC) - 2 (g/kg)
Wallpaper Adhesive
Product Detail:
1. Net Weight - 400(g)
2. Excellent performance in all kinds of wallpaper, es pecially the ones made by heavy and embossed papers.
3. Qualified for GB 18583-2008
General Speicification:
1. Concentration of Free Formaldehyde - less than 0.2 (g/kg)
Black RTV Silicone Gasket Maker(85G)
Black RTV Silicone Gasket Maker(85G)
1.China Top10 Factory
2.Strong supply capacity and delivery fast.
3.ISO,CE,SOCAP,SASO..
Black RTV Silicone Gasket Maker(85G)
one-part, non-slumping, acetate-curing rubber paste that cures to a permanently flexible silicone rubber on exposure to atmospheric moisture at room temperature. It is permanently flexible and stable at temperatures from -76°F to 536°F (-60°C to 280°C). It is also highly resistant to oil, water, weather, vibration and grease. Ideal application for valve covers, oil pans, timing covers, water pumps, thermostat housings, intake manifold and seals.
Typical application:
drive housings, exhaust manifolds, thermostat housings, valve covers, water pumps, different covers
LZ3601v hi-temp red RTV silicone gasket maker is single-component, non-sl umping, neutral-curing rubbe
LZ3601 hi-temp red RTV silicone gasket maker is single-component, non-slumping, neutral-curing rubber paste that cures to a permanently flexible silicone rubber on exposure to atmospheric moisture at room temperature. Formulated for hi-temp applications, or heavy duty use (such as towing, etc), replaces almost any cut gasket by making reliable "formed-in-place" gaskets that resist cracking or shrinking,and migrating caused by thermal cycling. Coats pro-cut gaskets to increasereliability. Temperature range -76°F to 600°F (-60°C to 300°C)intermittent. Resists auto and shop fluids.
Qty/ctn:12pcs
G.W.:1.4KG
N.W.:1.2KG
comma car care products:
1.China Top10 Factory
2.Strong supply capacity and delivery fast.
3.ISO,CE,SOCAP,SASO..
Black RTV Silicone Gasket Maker(85G)
one-part, non-slumping, acetate-curing rubber paste that cures to a permanently flexible silicone rubber on exposure to atmospheric moisture at room temperature. It is permanently flexible and stable at temperatures from -76°F to 536°F (-60°C to 280°C). It is also highly resistant to oil, water, weather, vibration and grease. Ideal application for valve covers, oil pans, timing covers, water pumps, thermostat housings, intake manifold and seals.
Typical application:
drive housings, exhaust manifolds, thermostat housings, valve covers, water pumps, different covers
LZ3601v hi-temp red RTV silicone gasket maker is single-component, non-sl umping, neutral-curing rubbe
LZ3601 hi-temp red RTV silicone gasket maker is single-component, non-slumping, neutral-curing rubber paste that cures to a permanently flexible silicone rubber on exposure to atmospheric moisture at room temperature. Formulated for hi-temp applications, or heavy duty use (such as towing, etc), replaces almost any cut gasket by making reliable "formed-in-place" gaskets that resist cracking or shrinking,and migrating caused by thermal cycling. Coats pro-cut gaskets to increasereliability. Temperature range -76°F to 600°F (-60°C to 300°C)intermittent. Resists auto and shop fluids.
Qty/ctn:12pcs
G.W.:1.4KG
N.W.:1.2KG
comma car care products:
hotmelt adhesive web
1.For interling etc
2.Material:polyamide
3.Item:hotmelt adhesive web
4.Color:milky white
5.Mobile:008618939758527
H-1001w (Hotmelt adhesive web or Double sides adhesive)polyamide
The hot melt adhesive webs is net-like bond matetial fused from Copolyamide.It has high bond intensity,used for hot melt bond between textile materials,non-woven fabric,the double cloth covers of dress,patterns,in field of the decorationmaterials,the car interior decoration,etc.
Performance characteristics are as follows:
1. The various types of textiles, metal materials, such as , badge,Embroidering with excellent adhesion properties.
2. A good washing resistance properties of 40 degrees.
3. This product is non - formaldehyde, non-toxic, is environmentally friendly products.
4. Breadth(cm):0-152 or Custom making
Pr oduct Specifications are as follows:
1. Item name:co-polyamide webs
2. Material: copolyamide
3. Melt Range:105-115
4. Press- temperature :135-160
5. The proposed processing pressure: 0.5 -1.5kg/cm2
6. Recommended processing times :5-20 sec Contact info: Mobile:0086-18939758527
2.Material:polyamide
3.Item:hotmelt adhesive web
4.Color:milky white
5.Mobile:008618939758527
H-1001w (Hotmelt adhesive web or Double sides adhesive)polyamide
The hot melt adhesive webs is net-like bond matetial fused from Copolyamide.It has high bond intensity,used for hot melt bond between textile materials,non-woven fabric,the double cloth covers of dress,patterns,in field of the decorationmaterials,the car interior decoration,etc.
Performance characteristics are as follows:
1. The various types of textiles, metal materials, such as , badge,Embroidering with excellent adhesion properties.
2. A good washing resistance properties of 40 degrees.
3. This product is non - formaldehyde, non-toxic, is environmentally friendly products.
4. Breadth(cm):0-152 or Custom making
Pr oduct Specifications are as follows:
1. Item name:co-polyamide webs
2. Material: copolyamide
3. Melt Range:105-115
4. Press- temperature :135-160
5. The proposed processing pressure: 0.5 -1.5kg/cm2
6. Recommended processing times :5-20 sec Contact info: Mobile:0086-18939758527
YT HIGH-TEMP RTV SILICONE SEALANT
YT HIGH-TEMP RTV SILICONE SEALANT valve covers, oil pans, exhaust manifolds, excellent heat control and torque retention.
YT HI-TEMP RTV SILICONE INSTANT GASKET is based on repairing norm for China auto company to develop neutral silicone sealant.The gaskets are enable to resist high Pressure, cracking, shrinking and migrating caused by thermal cycling. Temperature range from -85°F to 580°F (-65°C to 300°C) intermittent, ideal for water pumps and thermostat housing. Valve covers, oil pans, exhaust manifolds, intake manifolds, timing covers, excellent heat control and torque retention.
DIRECTIONS:
1. Clean and dry surfaces, erase completely all dirt & grease with a residue free solvent.
2. Take away the cap, puncture the inner seal, and screw on the nozzle cut at the desired bead sise.
3. Apply the beads eve nly around the perimeter or one surface.
4. Normally material skin in 15 minutes, assemble parts once silicone skins over.
5. Sealant is fully cured in 24 hours. Use the knife to remove excess silicone.
6. Clean the nozzle and put back the cap tightly after use. If the sealant cures in the nozzle,
remove the cured plug with a pin or paper clip.
NOTE:
1. Flexible and stable at all temperatures from -85°F to 580°F (-65°C to 300°C).
2. Not recommended for continuous immersion in gasoline.
3. Do not use instant gasket only when replacing cylinder head gaskets with predetermined
Tolerances.
CAUTION:
1. On contact, uncured sealant causes irritation, avoid contact of eyes and skin. In case of contact,
Flush eyes with water, remove from skin with a dry cloth and call physician immediately.
2. Use with adequate ventistion.
3. Use lid to tightly seal if it was not used up. Keep out of reach of children.
YT HI-TEMP RTV SILICONE INSTANT GASKET is based on repairing norm for China auto company to develop neutral silicone sealant.The gaskets are enable to resist high Pressure, cracking, shrinking and migrating caused by thermal cycling. Temperature range from -85°F to 580°F (-65°C to 300°C) intermittent, ideal for water pumps and thermostat housing. Valve covers, oil pans, exhaust manifolds, intake manifolds, timing covers, excellent heat control and torque retention.
DIRECTIONS:
1. Clean and dry surfaces, erase completely all dirt & grease with a residue free solvent.
2. Take away the cap, puncture the inner seal, and screw on the nozzle cut at the desired bead sise.
3. Apply the beads eve nly around the perimeter or one surface.
4. Normally material skin in 15 minutes, assemble parts once silicone skins over.
5. Sealant is fully cured in 24 hours. Use the knife to remove excess silicone.
6. Clean the nozzle and put back the cap tightly after use. If the sealant cures in the nozzle,
remove the cured plug with a pin or paper clip.
NOTE:
1. Flexible and stable at all temperatures from -85°F to 580°F (-65°C to 300°C).
2. Not recommended for continuous immersion in gasoline.
3. Do not use instant gasket only when replacing cylinder head gaskets with predetermined
Tolerances.
CAUTION:
1. On contact, uncured sealant causes irritation, avoid contact of eyes and skin. In case of contact,
Flush eyes with water, remove from skin with a dry cloth and call physician immediately.
2. Use with adequate ventistion.
3. Use lid to tightly seal if it was not used up. Keep out of reach of children.
Hot melt adhesive
HD Hot melt adhesive
We use international advanced equipments to smash materials (including engineering plastics, rubber, polyester, polypropylene etc.)
that could not be smashed in the normal temperature without breaking their molecular structure and function.
By using liquid ammonia as our cooling source, we can prevent certain materials from oxidation;
we can also prevent materials such as TPU from degradation,
which would otherwise happen under normal temperature.
We use ternary screening equipment to effectively separate
materials with various particle sizes;
therefore provide our customers with high quality services.
We use international advanced equipments to smash materials (including engineering plastics, rubber, polyester, polypropylene etc.)
that could not be smashed in the normal temperature without breaking their molecular structure and function.
By using liquid ammonia as our cooling source, we can prevent certain materials from oxidation;
we can also prevent materials such as TPU from degradation,
which would otherwise happen under normal temperature.
We use ternary screening equipment to effectively separate
materials with various particle sizes;
therefore provide our customers with high quality services.
Subscribe to:
Comments (Atom)